C-PRAV Technology Solutions · Australia & New Zealand

Rail EMC Testing

Railway electromagnetic compatibility (EMC) test solutions for rolling stock, onboard electronics, signalling, telecommunications and fixed rail power installations.

Application Overview

Railway EMC assessment considers emissions and immunity at equipment, subsystem, vehicle and infrastructure interfaces. C-PRAV supports test planning, pre-compliance investigations and the selection of suitable EMC test and measurement hardware for rail applications.

◆Rolling stock, locomotives, passenger trains, trams and light rail vehicles

◆Onboard control, monitoring, passenger information and entertainment systems

◆Traction converters, auxiliary power supplies, battery systems and chargers

◆Signalling, train detection, interlocking and trackside control equipment

◆Rail communications, radio systems, antennas and telemetry

◆Fixed installations, substations, power conversion and wayside equipment

Relevant Standards & Requirements

The references below are a technical starting point for rail EMC projects. Confirm the applicable edition, national adoption, amendments, contractual requirements, equipment category and test levels with the rail operator, project EMC plan and relevant standards publisher before testing.

Standard / reference
Scope and typical application

AS 7722:2026 – EMC Management

Australian rail-industry framework for managing electromagnetic emissions and susceptibility across railway systems and their lifecycle. Confirm project and operator requirements.

EN 50121-1 – General

Framework for railway EMC, system behaviour and management principles. Used with the relevant product-specific parts of the series.

EN 50121-2 – Whole railway system

Emission of the railway system to the outside world, including assessment at the railway boundary.

EN 50121-3-1 – Rolling stock: train and complete vehicle

Emission and immunity requirements for rolling stock at vehicle level, including the train/energy interface as defined by the standard.

EN 50121-3-2 – Rolling stock: apparatus

Conducted and radiated emissions and immunity for electrical/electronic apparatus intended for integration on rolling stock.

EN 50121-4 – Signalling and telecommunications apparatus

Emission and immunity requirements for signalling and telecommunications equipment installed within railway systems.

EN 50121-5 – Fixed power supply installations

Emission and immunity requirements for electrical/electronic apparatus and components used in railway fixed power-supply installations.

Important: EN 50121 parts address different railway domains and are not interchangeable. IEC 62236 is the corresponding international railway EMC series; for example, IEC 62236-3-2 addresses rolling-stock apparatus. EN 50155 addresses electronic equipment used on rolling stock and is a complementary equipment standard, not a replacement for EMC requirements. Confirm current editions and applicable Australian adoptions, including the project’s AS 7722 requirements.

Test Methods & Hardware Requirements

Typical railway EMC assessments are mapped below to commonly used instrumentation, test fixtures and accessories. The final setup depends on the applicable standard, test level, frequency range, EUT configuration, port type, operating mode and required measurement uncertainty.

Test / method
Purpose and typical assessment
Typical hardware and accessories

Rolling stock radiated emissions

Assess emissions from a complete train or vehicle against the applicable rolling-stock and railway-boundary requirements.

EMI receiver or spectrum analyser, calibrated antennas, preamplifiers, antenna masts, GPS/time reference and measurement software.

Apparatus conducted emissions

Measure conducted disturbances from onboard equipment at relevant power and signal interfaces.

EMI receiver, artificial networks or specified coupling networks, current probes, voltage probes and LISN where appropriate to the method.

Apparatus radiated emissions

Measure radiated electric- and magnetic-field emissions from onboard electronic equipment.

EMI receiver, broadband antennas, loop antennas, preamplifiers, turntable or controlled test arrangement and absorber-lined test space where required.

Conducted RF immunity

Evaluate equipment response to RF disturbances coupled onto power, control or signal cables.

RF signal generator, RF power amplifier, CDN or injection clamp/probe, directional coupler, power meter, current monitoring and EUT monitoring.

Radiated RF immunity

Evaluate equipment operation in defined radiated RF fields representative of the intended railway environment.

RF generator, broadband antennas, power amplifiers, field probe, field-monitoring system, power sensors and an appropriate test chamber or site.

Electrostatic discharge (ESD)

Assess immunity to electrostatic discharges at accessible points and interfaces where specified.

Calibrated ESD simulator, discharge tips, reference plane, coupling planes, ground connections and verification accessories.

Electrical fast transient and surge

Assess immunity to fast transients and surge events on applicable power or signal ports when required by the product specification.

EFT/burst and surge generators, coupling/decoupling networks, CDN, oscilloscope, voltage probes and current monitoring.

Low-frequency magnetic field immunity

Assess susceptibility to magnetic fields associated with traction currents, power equipment and nearby conductors.

Low-frequency signal source, power amplifier, field coils, calibrated magnetic-field probe and monitoring equipment.

Power supply disturbances and transients

Characterise equipment behaviour under specified supply variations, interruptions and transient conditions.

Programmable AC/DC source, power analyser, transient generator, oscilloscope, differential voltage probes and current probes.

Signalling and train-detection compatibility

Investigate electromagnetic interference risks at interfaces with track circuits, axle counters, signalling and train-control systems.

Selective voltmeter or spectrum analyser, EMI receiver, current/voltage probes, loop antennas, rail-current measurement accessories and recording system.

Railway site/boundary emission survey

Measure electromagnetic emissions around railway infrastructure or at defined site boundaries.

Portable EMI receiver or spectrum analyser, calibrated antennas, active loop, preamplifier, tripod, GNSS/GPS and logging software.

Fixed installation EMC assessment

Assess emissions and immunity of equipment associated with traction power, substations and fixed railway installations.

EMI receiver, spectrum analyser, current probes, antennas, field probes, power-quality analyser and suitable coupling/injection accessories.

Engineering & Test Planning Considerations

  • Identify the railway domain: rolling stock, onboard apparatus, signalling/telecommunications, fixed power installations or the whole railway system.
  • Define the operator’s EMC requirements, project EMC management plan, equipment interfaces, operating modes and acceptance criteria before selecting tests.
  • Consider traction supply, return currents, track circuits, axle counters, radio transmitters, cable routing, bonding, earthing and installation locations.
  • Choose conducted and radiated tests according to the applicable part of EN 50121 / IEC 62236 and relevant Australian requirements; generic industrial EMC tests do not automatically demonstrate railway compliance.
  • Record EUT configuration, cable layout, software/operating state, performance criteria, test deviations and results so evidence can be reviewed against the project requirements.
  • Formal testing, on-track measurements and specialist high-power or vehicle-level work require suitable facilities, competent personnel and an agreed safety/access plan.

C-PRAV Tech Manufacturer & Technology Portfolio

C-PRAV Tech can help identify and configure test and measurement solutions using the following manufacturers. Product selection is application-dependent and subject to model availability, options, calibration and suitability for the governing rail test method.

Keysight

EMI receivers, spectrum analysers, RF signal generators, vector network analysers, oscilloscopes, power analysers, programmable power supplies and electronic loads.

PRIMA

EMC immunity test systems and equipment for ESD, EFT/burst, surge and transient testing, subject to the required rail method and test level.

Tekbox

LISNs, current probes, near-field probes, antennas, coupling/decoupling networks and EMC pre-compliance accessories.

Laplace Instruments

EMI receivers, LISNs, antennas, CDNs, RF amplifiers and EMC measurement accessories.

Siglent

Oscilloscopes, spectrum analysers, RF generators, vector network analysers and programmable power supplies.

Micsig

Oscilloscopes and differential/current probes for electrical and transient measurements.

Harogic

Compact and portable RF spectrum analysers for laboratory, field and troubleshooting measurements.

SINUO

Environmental and temperature/humidity test equipment that may support complementary rail equipment qualification programmes, subject to method suitability.

C-PRAV Labs & Engineering Support

C-PRAV Technology Solutions Pty Ltd  – Melbourne, Australia

C-PRAV Tech supports EMC, electrical safety, radio, RF exposure, environmental and product compliance activities. For rail applications, support may include test planning, pre-compliance investigation, engineering troubleshooting and selection or demonstration of suitable test equipment. Formal rail certification, on-track testing and accredited scope must be confirmed for each specific requirement before making a compliance claim.

Laboratory: Hallmarc Business Park, A9/2A Westall Road, Springvale VIC 3171, Australia

Plan Your Next Compliance or R&D Test

Talk to C-PRAV Tech about your rail product, intended installation, target market, operator requirements and applicable standards. We can help identify a practical test approach and suitable instrumentation or test-system configuration.

Technical and accreditation note: This page is general technical guidance, not a declaration of conformity or guarantee of compliance. Verify current editions, national adoptions and project-specific requirements with the rail operator, standards publisher and relevant authorities. Laboratory accreditation and test capability are method- and scope-specific; confirm the applicable scope and facility before committing to formal testing.