Railway electromagnetic compatibility (EMC) test solutions for rolling stock, onboard electronics, signalling, telecommunications and fixed rail power installations.
Railway EMC assessment considers emissions and immunity at equipment, subsystem, vehicle and infrastructure interfaces. C-PRAV supports test planning, pre-compliance investigations and the selection of suitable EMC test and measurement hardware for rail applications.
◆Rolling stock, locomotives, passenger trains, trams and light rail vehicles
◆Onboard control, monitoring, passenger information and entertainment systems
◆Traction converters, auxiliary power supplies, battery systems and chargers
◆Signalling, train detection, interlocking and trackside control equipment
◆Rail communications, radio systems, antennas and telemetry
◆Fixed installations, substations, power conversion and wayside equipment
The references below are a technical starting point for rail EMC projects. Confirm the applicable edition, national adoption, amendments, contractual requirements, equipment category and test levels with the rail operator, project EMC plan and relevant standards publisher before testing.
AS 7722:2026 – EMC Management
Australian rail-industry framework for managing electromagnetic emissions and susceptibility across railway systems and their lifecycle. Confirm project and operator requirements.
EN 50121-1 – General
Framework for railway EMC, system behaviour and management principles. Used with the relevant product-specific parts of the series.
EN 50121-2 – Whole railway system
Emission of the railway system to the outside world, including assessment at the railway boundary.
EN 50121-3-1 – Rolling stock: train and complete vehicle
Emission and immunity requirements for rolling stock at vehicle level, including the train/energy interface as defined by the standard.
EN 50121-3-2 – Rolling stock: apparatus
Conducted and radiated emissions and immunity for electrical/electronic apparatus intended for integration on rolling stock.
EN 50121-4 – Signalling and telecommunications apparatus
Emission and immunity requirements for signalling and telecommunications equipment installed within railway systems.
EN 50121-5 – Fixed power supply installations
Emission and immunity requirements for electrical/electronic apparatus and components used in railway fixed power-supply installations.
Important: EN 50121 parts address different railway domains and are not interchangeable. IEC 62236 is the corresponding international railway EMC series; for example, IEC 62236-3-2 addresses rolling-stock apparatus. EN 50155 addresses electronic equipment used on rolling stock and is a complementary equipment standard, not a replacement for EMC requirements. Confirm current editions and applicable Australian adoptions, including the project’s AS 7722 requirements.
Typical railway EMC assessments are mapped below to commonly used instrumentation, test fixtures and accessories. The final setup depends on the applicable standard, test level, frequency range, EUT configuration, port type, operating mode and required measurement uncertainty.
Rolling stock radiated emissions
Assess emissions from a complete train or vehicle against the applicable rolling-stock and railway-boundary requirements.
EMI receiver or spectrum analyser, calibrated antennas, preamplifiers, antenna masts, GPS/time reference and measurement software.
Apparatus conducted emissions
Measure conducted disturbances from onboard equipment at relevant power and signal interfaces.
EMI receiver, artificial networks or specified coupling networks, current probes, voltage probes and LISN where appropriate to the method.
Apparatus radiated emissions
Measure radiated electric- and magnetic-field emissions from onboard electronic equipment.
EMI receiver, broadband antennas, loop antennas, preamplifiers, turntable or controlled test arrangement and absorber-lined test space where required.
Conducted RF immunity
Evaluate equipment response to RF disturbances coupled onto power, control or signal cables.
RF signal generator, RF power amplifier, CDN or injection clamp/probe, directional coupler, power meter, current monitoring and EUT monitoring.
Radiated RF immunity
Evaluate equipment operation in defined radiated RF fields representative of the intended railway environment.
RF generator, broadband antennas, power amplifiers, field probe, field-monitoring system, power sensors and an appropriate test chamber or site.
Electrostatic discharge (ESD)
Assess immunity to electrostatic discharges at accessible points and interfaces where specified.
Calibrated ESD simulator, discharge tips, reference plane, coupling planes, ground connections and verification accessories.
Electrical fast transient and surge
Assess immunity to fast transients and surge events on applicable power or signal ports when required by the product specification.
EFT/burst and surge generators, coupling/decoupling networks, CDN, oscilloscope, voltage probes and current monitoring.
Low-frequency magnetic field immunity
Assess susceptibility to magnetic fields associated with traction currents, power equipment and nearby conductors.
Low-frequency signal source, power amplifier, field coils, calibrated magnetic-field probe and monitoring equipment.
Power supply disturbances and transients
Characterise equipment behaviour under specified supply variations, interruptions and transient conditions.
Programmable AC/DC source, power analyser, transient generator, oscilloscope, differential voltage probes and current probes.
Signalling and train-detection compatibility
Investigate electromagnetic interference risks at interfaces with track circuits, axle counters, signalling and train-control systems.
Selective voltmeter or spectrum analyser, EMI receiver, current/voltage probes, loop antennas, rail-current measurement accessories and recording system.
Railway site/boundary emission survey
Measure electromagnetic emissions around railway infrastructure or at defined site boundaries.
Portable EMI receiver or spectrum analyser, calibrated antennas, active loop, preamplifier, tripod, GNSS/GPS and logging software.
Fixed installation EMC assessment
Assess emissions and immunity of equipment associated with traction power, substations and fixed railway installations.
EMI receiver, spectrum analyser, current probes, antennas, field probes, power-quality analyser and suitable coupling/injection accessories.
C-PRAV Tech can help identify and configure test and measurement solutions using the following manufacturers. Product selection is application-dependent and subject to model availability, options, calibration and suitability for the governing rail test method.
EMI receivers, spectrum analysers, RF signal generators, vector network analysers, oscilloscopes, power analysers, programmable power supplies and electronic loads.
EMC immunity test systems and equipment for ESD, EFT/burst, surge and transient testing, subject to the required rail method and test level.
LISNs, current probes, near-field probes, antennas, coupling/decoupling networks and EMC pre-compliance accessories.
EMI receivers, LISNs, antennas, CDNs, RF amplifiers and EMC measurement accessories.
Oscilloscopes, spectrum analysers, RF generators, vector network analysers and programmable power supplies.
Oscilloscopes and differential/current probes for electrical and transient measurements.
Compact and portable RF spectrum analysers for laboratory, field and troubleshooting measurements.
Environmental and temperature/humidity test equipment that may support complementary rail equipment qualification programmes, subject to method suitability.
C-PRAV Technology Solutions Pty Ltd – Melbourne, Australia
C-PRAV Tech supports EMC, electrical safety, radio, RF exposure, environmental and product compliance activities. For rail applications, support may include test planning, pre-compliance investigation, engineering troubleshooting and selection or demonstration of suitable test equipment. Formal rail certification, on-track testing and accredited scope must be confirmed for each specific requirement before making a compliance claim.
Laboratory: Hallmarc Business Park, A9/2A Westall Road, Springvale VIC 3171, Australia
Contact: sales@c-pravtech.com · +61 3 9087 9383
Talk to C-PRAV Tech about your rail product, intended installation, target market, operator requirements and applicable standards. We can help identify a practical test approach and suitable instrumentation or test-system configuration.
Technical and accreditation note: This page is general technical guidance, not a declaration of conformity or guarantee of compliance. Verify current editions, national adoptions and project-specific requirements with the rail operator, standards publisher and relevant authorities. Laboratory accreditation and test capability are method- and scope-specific; confirm the applicable scope and facility before committing to formal testing.